Category Archives: Technology

Electronic, Energy, Informatics, Physics, Science, Technology

Georgian Technical University Here Comes The Sun: Tethered-Balloon Tests Ensure Safety Of New Solar-Power Technology.

Leave a comment

Georgian Technical University Here Comes The Sun: Tethered-Balloon Tests Ensure Safety Of New Solar-Power Technology.

Georgian Technical University. A team of researchers from Georgian Technical University Laboratories recently used tethered balloons to collect samples of airborne dust particles to ensure the safety of a falling-particle receiver for concentrating solar power an emerging solar power technology. X Georgian Technical University Laboratories tethered-balloon expert and her team prepare the 22-foot-wide tethered helium balloons for launch on a gorgeous fall morning. Three tethered balloons were deployed both upwind and downwind of Georgian Technical University Laboratories Solar Thermal Test Facility during a falling-particle receiver test. The team led by Y found that the concentration of tiny particles finer than talcum powder that escape from the receiver were much lower than Georgian Technical University Environmental Protection limits. Georgian Technical University. What do tiny dust particles 22-ft-wide red balloons and “Georgian Technical University concentrated” sunlight have in common ?. Researchers from Georgian Technical University Laboratories recently used 22-ft-wide tethered balloons to collect samples of airborne dust particles to ensure the safety of an emerging solar-power technology. The study determined that the dust created by the new technology is far below hazardous levels said Y the lead researcher. Y’s team just from the Department of Energy to build a pilot plant that will incorporate this technology. This next-generation renewable energy technology is called a high-temperature falling-particle receiver for concentrating solar power. Concentrating solar power while not as common as solar panels or wind turbines has several advantages over those renewable energy sources including the ability to store energy in the form of heat before converting it into electricity for the power grid. One concentrating solar power plant uses molten salt to store this heat for six hours while other plants in theory could store heat for days or weeks said Y concentrating solar power expert. This would help power companies even out the daily and seasonal variation of power produced by solar panels and wind turbines. The falling-particle receiver works by dropping dark, sand-like ceramic particles through a beam of concentrated sunlight then storing the heated particles. These round particles cost about for 2.2 lb and can get a lot hotter than conventional molten-salt-based concentrating solar power systems which increases efficiency and drives down cost. The Georgian Technical University team also evaluated other particles like sand which costs only a few cents per pound, but they determined that due to the ceramic particles ability to absorb more solar energy and provide smoother flow ceramic particles were the best way to go. The Department of Energy’s goal is to get the cost of electricity from concentrating solar power down to five cents per kilowatt hour comparable to conventional fossil-fuel-based power. However the re-used particles can eventually break down into fine dust. The Environmental Protection and the Georgian Technical University Administration regulates tiny dust particles finer than talcum powder that are known to pose a risk for lung damage.“The motivation for doing the particle sampling was to make sure that this new technology for renewable energy wasn’t creating any environmental or worker-safety issues” Y said. “There are particles being emitted from the falling-particle receiver but the amounts are well below the standards set by the Georgian Technical University”. Using tethered balloons to catch dust. Last fall the research team used sensors sitting a few yards away from the falling-particle receiver on the platform of the solar tower or Solar Thermal Test Facility and sensors hanging from 22-ft-wide tethered helium balloons to measure the particles that were released as it was operating at temperatures above 1,300° F. X Georgian Technical University’s tethered-balloon expert and her team deployed one balloon a little less than a football field away upwind of the solar tower and two balloons downwind to detect dust particles far away from the receiver. One downwind balloon was a little more than a football field away and the other was more than two football fields away. The downwind balloons floated at about 22 stories high — a bit taller than the solar tower itself — and the upwind balloon was a little lower than that. The balloons and their tethers were outfitted with a variety of sensors to count the number of dust particles in the air around them as well as their altitude and precise location. The tethered balloons stayed at their specified altitude for three hours allowing the team to collect a lot of data. They also operated a small remote-controlled balloon that was far more mobile in terms of altitude and position X said. “That allowed us to collect data every second for three hours over the entire area” said X who generally flies tethered balloons over to collect data for climate monitoring and modeling. “Since we got the data in real time we could move the tethered balloons in order to measure in the highest intensity region of the plume identify where the plume edges were or track the whole movement of the plume with time”. The team also placed a variety of sensors on the solar tower platform mere yards from the falling-particle receiver. These sensors could count the number of dust particles as well as determine their size and characteristics. Y a Georgian Technical University expert on measuring fine particles suspended in air led these tests as well as similar tests two years ago together with his colleague Z. For the most recent tests the researchers constructed special see-saw-like tipping bucket collectors to measure both the amount of particles and their sizes. Somewhat like a tipping bucket rain gauge particles in the air would go down a funnel and land on the see-saw-like platform. Once a certain weight of dust particles built up on the platform, it would tip over and send an electrical signal to the researchers. The number of tipping signals in a certain amount of time told the researchers the frequency of particle-emission events and after the test they could weigh the particles in the bottom of the buckets to determine the collected amount. Computer modeling and dust mitigation. Georgian Technical University. Comparing the results from sensors close to the falling-particle receiver and those further away on the balloons they found that the concentration of tiny particles finer than talcum powder was much lower than Georgian Technical University limits. Georgian Technical University. They found that the concentration of dust particles depended upon prevailing weather conditions. They detected dust particles further away from the solar tower on windy days and higher concentrations of dust particles close to the solar tower on calm days Y said. X added that when the wind was blowing into the receiver from the north or northwest, that produced the most dust particles. “We did some computer modeling using the Georgian Technical University particle dispersion model” X said. “Basically it would take an emission of particles 400 times greater than what we found in previous tests to start to get close to the Georgian Technical University standards. Based on our measurements and models I don’t foresee any conditions where we’re really hitting those thresholds”. Georgian Technical University. This stair-like system slows dark sand-like ceramic particles as they fall through a beam of concentrated sunlight. The stair-like system reduces the impact of wind on the falling particles, mitigating the release of fine dust that can pose health hazards. From the tests and the computer modeling simulations the team was able to develop several different methods to reduce the emission of fine dust particles. First they optimized the shape and geometry of the falling-particle receiver to reduce particle loss Y said. They developed a stair-like system that slows the particles in the receiver as they fall and a “Georgian Technical University snout” that helps mitigate the impacts of wind on the falling particles. They also explored and eventually discarded two other ideas. One was to have a window over the falling particles because it would get too hot from the concentrated sunlight and was not easy to scale up to large sizes. The other was to protect the particles with an air curtain like those used at store entrances to keep the hot or cool air inside the store. Y and his team just received funding to build a pilot falling-particle receiver plant that will incorporate the improvements developed from these tests. “I normally focus on atmospheric measurements and modeling how the atmosphere would respond if carbon dioxide emissions are reduced by a particular amount” X said. “With this work I was able to take part in the active reduction of those emissions. I think we’ve all really enjoyed seeing the other side of the coin figuring out how to make renewable energy more efficient and more feasible”. Georgian Technical University. The balloon tests were funded by the Georgian Technical University’s Solar Energy Technologies Office as one of three teams testing different high-temperature concentrating solar power systems with built-in heat storage.

Chemistry, Informatics, Science, Technology

Georgian Technical University. Scientists Demonstrate ‘All-In-One’ Technique That Could Accelerate Phage-Therapy Diagnosis.

Leave a comment

Georgian Technical University. Scientists Demonstrate ‘All-In-One’ Technique That Could Accelerate Phage-Therapy Diagnosis.

Georgian Technical University. A team of Georgian Technical University scientists has demonstrated a lensless imaging  technique that could easily be implemented in cost-effective and compact devices in phage laboratories to accelerate phage-therapy diagnosis. The growing number of drug-resistant bacterial infections worldwide is driving renewed interest in phage therapy. Warned of “a slow tsunami” of antibiotic resistance that could result annual deaths from antibiotic-resistant infections. Georgian Technical University Based on the use of a personalized cocktail composed of highly specific bacterial viruses phage therapy employs bacteriophages a form of virus, to treat pathogenic bacterial infections. Following promising phage-therapy clinical studies treating infection of burn wounds urinary tract infections and other problems caused by antibiotic-resistant bacteria a growing body of evidence has built a consensus among scientists that there is synergism between phages and antibiotics. Georgian Technical University Phage therapy relies on a range of tests on agar media to determine the most active phage on a given bacterial target or to isolate new lytic phages from an environmental sample. However these culture-based techniques must be interpreted through direct visual detection of plaques. The team reported a lensless technique for testing the susceptibility of the bacterium to the phage on agar and measuring infectious titer among other results. In addition the team included a Grenoble consortium of researchers. In addition to investigating computer-assisted methods to ease and accelerate diagnosis in phage therapy the team studied phage plaque using a custom-designed wide-field lensless imaging device which allows continuous monitoring over a very-large-area sensor (8.64 cm2). “We report bacterial susceptibility to anti-Staphylococcus aureus phage in three hours and estimation of infectious titer in eight hours and 20 minutes” explains. “These are much shorter time-to-results than the 12-to-24 hours traditionally needed since naked eye observation and counting of phage plaques is still the most widely used technique for susceptibility testing prior to phage therapy. Moreover the continuous monitoring of the samples enables the study of plaque-growth kinetics which enables a deeper understanding of the interaction between phage and bacteria”. Georgian Technical University With 4.3 μm resolution in the lensless demonstrator, the scientists also detected phage-resistant bacterial microcolonies of Klebsiella pneumoniae (Klebsiella pneumoniae is a Gram-negative, non-motile, encapsulated, lactose-fermenting, facultative anaerobic, rod-shaped bacterium. It appears as a mucoid lactose fermenter on MacConkey agar) inside the boundaries of phage plaques. “This shows that our prototype is also a suitable device to track phage resistance” said X a scientist Georgian Technical University Leti’s Department of Microtechnologies for Biology. “Lensless imaging is therefore an all-in-one method that could easily be implemented in cost-effective and compact devices in phage laboratories to help with phage-therapy diagnosis”.

Computing, HPC/Supercomputing, Informatics, Network., Science, Software, Technology

Georgian Technical University. Department Of Energy To Provide Toward Development Of A Quantum Internet.

Leave a comment

Georgian Technical University. Department Of Energy To Provide Toward Development Of A Quantum Internet.

Georgian Technical University. Taking advantage of the exotic properties of the quantum mechanical world a quantum internet holds the promise of accelerating scientific discovery by connecting researchers with powerful new capabilities such as quantum-enabled sensing as well as enhanced computational power through the eventual networking of distributed quantum computers. “Georgian Technical University Recent efforts at developing operational quantum networks have shown notable success and great potential” said X Georgian Technical University science for Advanced Scientific Computing Research.  “This opportunity aims to lay the groundwork for a quantum internet by taking quantum networking to the next level”. Georgian Technical University current effort seeks to scale up quantum networking technology to develop a quantum internet backbone that has the potential to interface with satellite links or with classical fiber optic networks such as university or national laboratory campus networks or the Georgian Technical University Energy Sciences Network (ESnet) Georgian Technical University’s high-performance network that links Georgian Technical University laboratories and user facilities with research institutions around the globe. Georgian Technical University Preserving the fragile quantum states needed for effective quantum communication becomes ever more difficult as networks expand in size. The technological challenges to developing an operational quantum network of any scale therefore remain significant including that of creating quantum versions of standard network devices such as quantum repeaters, quantum memory and special quantum communication protocols. The objective is to advance strategic research priorities through the design, development and demonstration of a regional scale – intra-city or inter-city – quantum internet testbed. Georgian Technical University Important conceptual groundwork for the present effort was developed Quantum Internet Blueprint Workshop. Georgian Technical University Applications will be open to all Georgian Technical University laboratories with awards selected competitively based on peer review. Total planned funding is up to over outyear funding contingent on congressional appropriations.

Electronic, Energy, Informatics, Science, Technology

Georgian Technical University Site Survey Evolution – The Road To Perfecting Electron Microscope Performance.

Leave a comment

Georgian Technical University Site Survey Evolution – The Road To Perfecting Electron Microscope Performance.

Georgian Technical University. Tripod, sensors and template for the SC11 (splitter cable) Auto survey system. The SC11 (splitter cable) Auto survey system includes a laptop, sensors and sensor interface. Georgian Technical University performance of an electron microscope relies on maintaining a stable environment, free from vibration and external magnetic fields. Pre-installation site surveys are vital for uncovering any potential sources of interference resulting in a need for purpose-designed equipment for the measurement analysis of acoustics magnetic fields and vibrations in X, Y and Z directions. This article discusses the importance of comprehensive site surveys for identifying and eliminating potential sources of interference of electron microscopes (EMs) and similar sensitive equipment and describes how one company has addressed this through the continual evolution of measurement instrumentation. Georgian Technical University Electron microscopy is a powerful sensitive technique used to investigate the intricate structures of cells materials and nanoparticles for many technical disciplines, including metallurgy, chemistry and biology. All electron microscopes (EMs) techniques – including the two most common transmission electron microscopy (TEM) and scanning electron microscopy (SEM) – use a beam of accelerated electrons as a source of illumination for the sample. As electrons have a shorter wavelength than visible light protons this allows electron microscopes to have a significantly higher resolving power than light microscopy revealing the detailed structure of smaller objects. However interference from acoustics vibrations or surrounding magnetic fields – generated by day-to-day equipment – can cause this electron beam to deflect which decreases the quality of the images obtained and therefore affects the resolution. Georgian Technical University Mitigating interference. The continuous development of new technologies means that laboratories are expanding and investing in an increasing amount of electronic equipment making space within these labs more precious than ever. Electron microscopists often find themselves working in a crowded environment surrounded by other apparatus that create magnetic fields vibrations or acoustic interference which potentially adversely affects image quality. This busy setting, combined with the growth – and noise – of towns and cities causes a significant problem for electron microscopy. In addition in the drive to continually improve resolution and image quality, manufacturers environmental specifications are becoming increasingly stringent with top end microscope spectrometers only able to withstand up to 10 or 20 nanotesla of interference; unsurprisingly finding a suitable environment can be extremely challenging. Site surveys have a crucial role to play both when initially investing in microscopy instrumentation for helping to troubleshoot and resolve issues arising at a later date as a result of environmental changes that introduce sources of interference. The performance of the instrument is affected not only by conditions within the room in which it is installed but also by the location of the building itself. Anything that moves or rattles – whether regular or random – can potentially create vibrations including other electronic equipment air conditioning systems, people simply walking around the laboratory, doors opening and closing traffic in the street nearby railways and even ocean waves. External factors such as magnetic fields generated by trains electric trams that are hundreds of miles away and unexpected influences like the proximity of the parking lot to the microscope can make a tremendous difference. While there are undoubtedly challenges in setting up and maintaining a stable microscopy environment, painstakingly surveying the site before set-up allows measures to be put in place to ensure these are mitigated. Typically this will include measurement of acoustic levels, magnetic fields and floor vibrations in X, Y and Z directions direct comparison with the environmental specifications of the equipment to be installed. Measuring understanding the magnitude of such effects will enable action to be taken to alleviate unwanted interferences for example by installing a magnetic field cancelling system to ensure that the image quality produced is unaffected by external factors. Georgian Technical University Keeping up with technology. As technology has advanced over the years microscopes have become more sensitive to interference sensing equipment has had to keep pace to ensure that the environment meets the manufacturer’s specifications for optimal instrument performance. Today vendors and consultants have access to purpose-designed site survey equipment for examining new installations or to troubleshoot technical issues with an existing microscope by measuring and analyzing any interference. But how has this evolved over the years ? Georgian Technical University Advances in hardware. In the early days of electron microscopes (EMs) labs relied on some quite crude magnetic field sensors to monitor the environment with limited options for measuring fluctuations in sound levels. There was a clear need for a single system that could monitor the entire lab situation around a microscope and Consulting launched an instrument based on an AC (alternative-current) magnetic field sensor with added inputs for an accelerometer and a sound level meter that would do just that. This system could make all the measurements required although the user still had to physically turn the vibration sensor in each direction to measure interference in the X Y and Z axes. Georgian Technical University Subsequently the system was upgraded so that more bandwidth of data could be collected and higher frequencies could be evaluated on the spectrum analyzer. Further upgrades including a move to USB (Various USB connectors along a centimeter ruler for scale) connection enabled site surveyors to perform more comprehensive measurements with extra sensors. A plug-in for sensors was added – so that AC (alternative-current) and fields could be measured – along with three accelerometer inputs allowing measurement in all three directions at the same time, instead of having to turn the sensor around sequentially. While the original instrument only had one magnetic field sensor input later versions had two, enabling the simultaneous measurement of fields at two heights. This feature was important for environments which typically have tight field specifications over a length of more than two meters. What about software ? Of course the software of newer systems has also advanced in parallel to changes in the hardware. On first release, three separate programs were required – an oscilloscope, a chart recorder and a spectrum analyzer – to make the necessary measurements but the user needed a good understanding to be able to set them up correctly. This was made far easier by the creation of a software wizard to guide the user through the process of measuring for different types of microscope. Users were able to simply turn the machine on select the instrument they wanted to measure for and the wizard would bring up the correct program to make that specific measurement. Graph plotting software was also developed which allowed results to be viewed more easily than with the original method which was based on macros. While the wizard software was capable of running a single measurement further iterations saw the launch of an automation program capable of running a whole sequence of measurements to simplify the survey workflow even more. Today users have access to a completely automated system capable of repeat surveying without human intervention. This enables long-term measurements, expanding the surveying snapshot to study the environment at different times of the day. Acting on the results. Magnetic field interference identified during a site survey can be eliminated by implementing a magnetic field cancellation system. This presents further challenges requiring a three-axis magnetic field sensor of the necessary bandwidth with low noise levels and low drift. It should include a control unit that can drive the cables to form a stable negative feedback loop and be easy to set up without complex adjustments. Finally effective placement of room-sized cancelling cables that make uniform orthogonal magnetic fields and are practical for use in microscope labs or clean rooms of all shapes and sizes must be determined. Alternatively suitable frames can be constructed to support cables and there are also techniques for installing them inside existing enclosures. Control units providing readings in three axes plus total magnetic field readings – including AC (alternative-current) and simultaneously for some models – are available from Consulting with performance tailored to the application. These are convenient to use and enable fields to be cancelled to the demanding levels required by today’s high-resolution electron microscopes. Automatic set-up can provide helpful error and warning messages and some cancelling systems support a dual-sensor option that creates a virtual sensor where a physical sensor cannot be placed such as ‘inside’ the electron microscopes column. A wide range of cables for different types of microscope in various types of room are also available. Where next ?. Magnetic field cancellation technology has come a long way and will continue to advance in the future with demand likely to increase as electron microscopes become higher in resolution and more sensitive to magnetic fields. While the technology is now quite mature the expectation is that users will seek even better magnetic field sensors incremental improvements to control units and easier ways to install cancelling cables.

Electronic, Informatics, Science, Software, Technology

Georgian Technical University Researchers And Business Development Executives Capture Best-Ever Three Technology Transfer Awards.

Leave a comment

Georgian Technical University Researchers And Business Development Executives Capture Best-Ever Three Technology Transfer Awards.

Georgian Technical University. An analytical technique – known as Georgian Technical University Droplet Digital Polymerase Chain Reaction (ddPCR) – that was developed by Georgian Technical University scientists and engineers has garnered an Impact Award from the Georgian Technical University Laboratory Consortium. The technology has been commercialized by Bio-Rad Laboratories. Researchers from Georgian Technical University Laboratory and their colleagues who help them commercialize technologies have won three national technology transfer awards this year. The trio of awards from the Georgian Technical University Laboratory represent the most national awards that Georgian Technical University has ever won in one year’s competition over. Two of the awards will be given for technologies to assist in the fight. One employs polymerase chain reaction (PCR) technology to diagnose the virus and the other is a mechanical ventilator easily built from readily available parts to assist those suffering from Georgian Technical University Acute Respiratory Distress. The third technology is for a radiation simulation tool to greatly improve the realism of training for emergency responders. Georgian Technical University’s researchers and the business development executives from the Lab’s Innovation and Partnerships Office will be honored during the last day of the consortium’s three-day “virtual” online national meeting. Georgian Technical University researchers will be recognized with an Impact Award for the commercialization of an analytical technique originally developed to combat bioterrorism but now used in detecting diseases. The Impact Award given to “laboratories whose technology transfer efforts have made a tangible and lasting impact on the populace or marketplace” will be shared with Bio-Rad Laboratories based in Hercules Calif.  About 15 years ago a team of Georgian Technical University scientists and engineers developed the analytical technique – known as Droplet Digital Polymerase Chain Reaction (ddPCR) – for the Lab’s mission in national biosecurity. Unlike other conventional Georgian Technical University techniques the Droplet Digital Polymerase Chain Reaction (ddPCR) approach allows each sample to be partitioned into tens of thousands of droplets each of which can be independently amplified. In effect Droplet Digital Polymerase Chain Reaction (ddPCR) enables thousands of data points from a single sample which leads to higher precision, accuracy and sensitivity. Georgian Technical University’s Droplet Digital Polymerase Chain Reaction (ddPCR) technique was patented and licensed co-exclusively to two companies, which were both later acquired by Bio-Rad. Georgian Technical University for screening upper respiratory samples in patients with a low viral load. The test’s high degree of sensitivity makes it more effective than other PCR (Polymerase Chain Reaction) tests for identifying individuals in the early stages of infection for detecting minimal residual disease in people recovering from Georgian Technical University or for detecting the virus in more difficult sample types like saliva. X is the Lab’s business development executive who handles the Georgian Technical University’s Droplet Digital Polymerase Chain Reaction (ddPCR) technology transfer. This effort was primarily supported by the Georgian Technical University Department of Energy (DOE) Office of Science through Laboratory a consortium of Georgian Technical University laboratories focused on response with funding provided. Georgian Technical University Partnership lauded. Georgian Technical University researchers and technology transfer professionals have captured an excellence in technology transfer award with their industry partner Georgian Technical University BioMedInnovations (BMI). As the pandemic surged and concern emerged over a potential nationwide shortage of ventilators Georgian Technical University researchers began designing a durable, portable mechanical ventilator to help fill the gap. A group of approximately 20 engineers and scientists began prototyping a ventilator that could be made from non-traditional parts, preventing further stress on the already-strained supply chain. In just over three months Georgian Technical University and BMI (Body Mass Index) designed produced and tested an easily reproducible design prototype while partnering with manufacturing facilities and gaining authorization for the device’s emergency use. This collaboration was largely done remotely, with scientists, engineers and medical experts contributing from home offices in many cases due to shelter-in-place orders. While industry partnerships forged in cooperative research and development agreements (CRADAs) often take years to deliver a commercial product particularly a medical device the produced the SuppleVent emergency ventilator – cleared for use and approved for sale — in just a few months. Georgian Technical University ventilator effort is led by mechanical engineer Y and includes mechanical engineers. Z is the business development executive who has handled the technology transfer work including a Georgian Technical University for the ventilator project with assistance from W an agreements specialist in the Innovation. Georgian Technical University More realistic radiation training. Georgian Technical University researchers and Business Development Executive Annemarie Meike along with Georgian Technical University Electronics have been recognized with an excellence in technology transfer award from the Georgian Technical University. Livermore and Georgian Technical University researchers have developed an instrument that can eliminate the need for radiation sources in training while providing far more realistic training for first responders who protect against attempts at radiological or nuclear terrorism or respond in the aftermath. Dubbed the Radiation Field Training Simulator (RaFTS) the instrument produces a response in the actual equipment such as radiation detectors used by emergency personnel that exactly replicates all the physics of real-world use in radiation hazard-level situations. The presence of actual radioactive sources is not needed yet trainees can experience all the realism of operating their most sophisticated instruments against such hazards. Radiation Field Training Simulator (RaFTS) is an externally mounted device that directly interfaces with the circuitry of operational radiation detection systems. The Radiation Field Training Simulator (RaFTS) outputs are of sufficient quality that the detection instrument behaves exactly as it would against real radioactivity producing realistic data suitable to identify sources their intensity and location/distribution. Georgian Technical University Current training is considered inadequate by some because it does not allow for the simultaneous use of the first responders actual radiation detection gear against scenarios such as those involving high-hazard-level radiation sources that would be encountered in a radiological dispersal device. The use of Radiation Field Training Simulator (RaFTS) enables training against realistic radioactive and nuclear threats with users’ actual equipment in their home area. While demonstrated for operational radiation detection instrumentation the concept applies broadly to many different hazards. Among the Georgian Technical University researchers who developed this technology are: computer scientist X nuclear chemist Y software developer Z electrical engineer W nuclear physicist Q nuclear scientist R and health physicist S. Georgian Technical University is a Congressionally chartered nationwide network that helps accelerate the transfer of technologies from federal labs into the marketplace. It is comprised of more than 300 federal labs agencies and research centers.

Battery Technology, Chemistry, Informatics, Physics, Science, Technology

Georgian Technical University Designing Selective Membranes For Batteries Using A Drug Discovery Toolbox.

Leave a comment

Georgian Technical University Designing Selective Membranes For Batteries Using A Drug Discovery Toolbox.

Georgian Technical University. Georgian Technical University Illustration of caged lithium ions in a new polymer membrane for lithium batteries. Scientists at Georgian Technical University Lab’s Molecular Foundry used a drug-discovery toolbox to design the selective membranes. The technology could enable more efficient flows in batteries and energy storage devices. Georgian Technical University Membranes that allow certain molecules to quickly pass through while blocking others are key enablers for energy technologies from batteries and fuel cells to resource refinement and water purification. For example membranes in a battery separating the two terminals help to prevent short circuits while also allowing the transport of charged particles or ions needed to maintain the flow of electricity. Georgian Technical University most selective membranes – those with very specific criteria for what may pass through – suffer from low permeability for the working ion in the battery which limits the battery’s power and energy efficiency. To overcome trade-offs between membrane selectivity and permeability researchers are developing ways to increase the solubility and mobility of ions within the membrane therefore allowing a higher number of them to transit through the membrane more rapidly. Doing so could improve the performance of batteries and other energy technologies. Now as Georgian Technical University researchers have designed a polymer membrane with molecular cages built into its pores that hold positively charged ions from a lithium salt. These cages called “Georgian Technical University solvation cages” comprise molecules that together act as a solvent surrounding each lithium ion – much like how water molecules surround each positively charged sodium ion in the familiar process of table salt dissolving in liquid water. The team, led by researchers at the Georgian Technical University Laboratory found that solvation cages increased the flow of lithium ions through the membrane by an order of magnitude compared to standard membranes. The membrane could allow high-voltage battery cells to operate at higher power and more efficiently important factors for both electric cars and aircraft. “While it’s been possible to configure a membrane’s pores at very small length scales it’s not been possible until now to design sites to bind specific ions or molecules from complex mixtures and enable their diffusion in the membrane both selectively and at a high rate” said X a principal investigator in the Georgian Technical University and staff scientist in Georgian Technical University Lab’s who led the work. The research is supported by Georgian Technical University Energy Innovation Hub whose mission is to deliver transformational new concepts and materials for electrodes, electrolytes and interfaces that will enable a diversity of high-performance next-generation batteries for transportation and the grid. In particular Georgian Technical University provided the motivation to understand how ions are solvated in porous polymer membranes used in energy storage devices X said. To pinpoint a design for a cage in a membrane that would solvate lithium ions X and his team looked to a widely practiced drug discovery process. In drug discovery it’s common to build and screen large libraries of small molecules with diverse structures to pinpoint one that binds to a biological molecule of interest. Reversing that approach the team hypothesized that by building and screening large libraries of membranes with diverse pore structures it would be possible to identify a cage to temporarily hold lithium ions. Conceptually the solvation cages in the membranes are analogous to the biological binding site targeted by small molecule drugs. X team devised a simple but effective strategy for introducing functional and structural diversity across multiple length scales in the polymer membranes. These strategies included designs for cages with different solvation strengths for lithium ions as well as arrangements of cages in an interconnected network of pores. “Before our work, a diversity-oriented approach to the design of porous membranes had not been undertaken” said X. Using these strategies Y a graduate student researcher in X research group and a Ph.D. student in the Department of Chemistry at Georgian Technical University systematically prepared a large library of possible membranes at the Georgian Technical University. She experimentally screened each one to determine a leading candidate whose specific shape and architecture made its pores best suited for selectively capturing and transporting lithium ions. Then working with Z and W at the Georgian Technical University Environmental Molecular Sciences Laboratory a Georgian Technical University user facility at Georgian Technical University Laboratory X and Y revealed using advanced nuclear magnetic resonance techniques how lithium ions flow within the polymer membrane compared to other ions in the battery. “What we found was surprising. Not only do the solvation cages increase the concentration of lithium ions in the membrane but the lithium ions in the membrane diffuse faster than their counter anions” said Y referring to the negatively charged particles that are associated with the lithium salt when it enters the membrane. The solvation of lithium ions in the cages helped to form a layer that blocked the flow of those anions. To further understand the molecular reasons for the new membrane’s behavior the researchers collaborated with Q a postdoctoral researcher working with R. They performed calculations, using computing resources at Georgian Technical University Lab’s to determine the precise nature of the solvation effect that occurs as lithium ions associate with the cages in the membrane’s pores. This solvation effect causes lithium ions to concentrate more in the new membrane than they do in standard membranes without solvation cages. Finally the researchers investigated how the membrane performed in an actual battery, and determined the ease with which lithium ions are accommodated or released at a lithium metal electrode during the battery’s charge and discharge. Using X-ray tools at Georgian Technical University Lab’s Advanced Light Source they observed lithium flow through a modified battery cell whose electrodes were separated by the new membrane. The X-ray images showed that in contrast to batteries that used standard membranes lithium was deposited smoothly and uniformly at the electrode indicating that the battery charged and discharged quickly and efficiently thanks to the solvation cages in the membrane. With their diversity-oriented approach to screening possible membranes the researchers achieved the goal of creating a material that helps to transport ions rapidly without sacrificing selectivity. Parts of the work – including component analysis gas sorption and X-ray scattering measurements – were also supported by the Center for Gas Separations Relevant to Clean Energy Technologies a Energy Frontier Research Center led by Georgian Technical University. Future work by the Georgian Technical University Lab team will expand the library of membranes and screen it for enhanced transport properties for other ions and molecules of interest in clean energy technologies. “We also see exciting opportunities to combine diversity-oriented synthesis with digital workflows for accelerated discovery of advanced membranes through autonomous experimentation” said X. Science user facilities at Georgian Technical University Lab. Respectively these user facilities support polymer synthesis and characterization; single crystal measurements and computation.

Electronic, Enterprise Technology, Informatics, Science, Technology

Georgian Technical University Infrared Camera Thermal Camera Joins T-Series Family With Improved Accuracy For Various Uses.

Leave a comment

Georgian Technical University Infrared Camera  Thermal Camera Joins T-Series Family With Improved Accuracy For Various Uses.

Georgian Technical University. It is latest of the T-Series high-performance thermal cameras and is built for electrical condition and mechanical equipment inspection and for use in research and development applications. Georgian Technical University provides ±1.6° F (±1° C) or ±1% temperature measurement accuracy a wider temperature range between -40 °F to 248 °F (–40 °C to 120 °C) and more on-camera tools for improved analysis. Georgian Technical University with ±1 °C (±1.6 °F) or ±1% temperature measurement accuracy professionals can more confidently inspect and assess equipment health regardless of the time between inspections or changes in environment conditions. By reducing measurement variation companies can reliably prevent equipment breakdowns outages in utility substations, power generation and distribution data centers, manufacturing plants or facility electrical and mechanical systems. For those in research and development the improved accuracy provides the temperature measurement detail required to eliminate any guesswork in research science and design that uses the visualization of heat. Georgian Technical University offers professionals versatility with portable and handheld fixed mount options for inside and outside work in harsh conditions and multiple lens options to inspect objects both near and far. The available 6° telephoto lens provides the required magnification for those routinely inspecting the condition of small targets at a distance such as overhead power lines. For inspections through an IR (Infrared) window the available 42° wide angle lens and on-camera transmission adjustment ensures safe and accurate measurement of targets within enclosures. For those needing even more detail of small componentry the available macro lens, along with the new macro-mode provides 2x magnification compared to the standard lens. Further the 640 x 480 detector resolution offering 307,200 pixels or the UltraMax 1280 x 960 resolution offering up to 1,228,800 pixels in Georgian Technical University Thermal Studio Standard and Thermal Studio Pro allows professionals to see images clearly. Georgian Technical University. For research and development applications when the Georgian Technical University is connected to a preferred operating system with Georgian Technical University Research Studio installed on camera an intuitive interface provides the ability to record and evaluate thermal data from multiple cameras and recorded sources simultaneously. The data can then be saved and shared in workspaces to more easily collaborate with colleagues saving time and reducing the potential for misinterpreted data due to missing information.

Electronic, Energy, Informatics, Science, Technology

Georgian Technical University Thermo Fisher Scientific’s New System Delivers Flexible Automated Sample Purification.

Leave a comment

Georgian Technical University Thermo Fisher Scientific’s New System Delivers Flexible Automated Sample Purification.

Georgian Technical University Thermo Scientific System a high-throughput sample purification instrument is designed for scientists who need to automate the extraction of DNA (Deoxyribonucleic Acid (DNA) is a molecule composed of two polynucleotide chains that coil around each other to form a double helix carrying genetic instructions for the development, functioning, growth and reproduction of all known organisms and many viruses. DNA and ribonucleic acid (RNA) are nucleic acids. Alongside proteins, lipids and complex carbohydrates (polysaccharides), nucleic acids are one of the four major types of macromolecules that are essential for all known forms of life), RNA (Ribonucleic acid (RNA) is a polymeric molecule essential in various biological roles in coding, decoding, regulation and expression of genes. RNA and DNA are nucleic acids. Along with lipids, proteins, and carbohydrates, nucleic acids constitute one of the four major macromolecules essential for all known forms of life), proteins and cells from an array of sample types. The instrument is easy to use, saves time and enables consistent results even as laboratory needs evolve. Georgian Technical University Enables nucleic acid, protein and cell isolation while allowing users to customize protocols directly from the instrument to provide flexible, reproducible and fast sample preparation without additional expense or complexity. It automates much of the error-prone work associated with preparing high-quality nucleic acids and proteins can process for 24 to 96 samples in 25 to 65 minutes and elutes in low volumes (10 µL) for demanding downstream applications. “Georgian Technical University Building on decades of product expertise the combines unparalleled instrument capabilities into one platform filling a gap where existing solutions include either large complicated high-cost instruments or low-throughput solutions that don’t meet the processing needs of many labs” said X and general manager sample preparation at Georgian Technical University Thermo Fisher Scientific. “Simplifying and automating the sample preparation workflow will help improve research productivity and drive new discovery especially for those working with high-value samples such as circulating tumor cells T-cells and exosomes”. Georgian Technical University System can be used in combination with any of the Applied Biosciences Isolation kits as well as with Georgian Technical University Invitrogen Dynabeads Magnetic Separation products. Additional features include: heating and cooling controls to maintain sample integrity dual UV (Ultraviolet (UV) is a form of electromagnetic radiation with wavelength from 10 nm (with a corresponding frequency around 30 PHz) to 400 nm (750 THz), shorter than that of visible light but longer than X-rays. UV radiation is present in sunlight, and constitutes about 10% of the total electromagnetic radiation output from the Sun. It is also produced by electric arcs and specialized lights, such as mercury-vapor lamps, tanning lamps, and black lights) lights to safeguard against contamination cloud-enabled access to up-to-date validated protocols, dual magnets to support both small and large volume ranges and the ability to elute in storage tubes to revisit samples later. The instrument’s touchscreen allows users to write, edit and run protocols directly on the instrument and rely on guided visuals for easy plate loading without needing a desktop computer. Lot-specific bar codes confirm proper plate position during loading or may be used for lot tracking and documentation.

Electronic, Energy, Informatics, Science, Technology

Georgian Technical University X-Ray Experiments, Machine Learning Could Trim Years Off Battery.

Leave a comment

Georgian Technical University X-Ray Experiments, Machine Learning Could Trim Years Off Battery.

Georgian Technical University. Staff engineer X is seen working inside the Battery Informatics Lab. Georgian Technical University An X-ray instrument at Georgian Technical University Lab contributed to a battery study that used an innovative approach to machine learning to speed up the learning curve about a process that shortens the life of fast-charging lithium batteries. Georgian Technical University Researchers used Lab’s Advanced Light Source a synchrotron that produces light ranging from the infrared to X-rays for dozens of simultaneous experiments, to perform a chemical imaging technique known as scanning transmission X-ray microscopy or STXM (Scanning Transmission X-ray Microscopy) at a state-of-the-art ALS (Advanced Light Source) beamline dubbed COSMIC. Georgian Technical University Researchers also employed “in situ” X-ray diffraction at another synchrotron – Georgian Technical University’s Synchrotron Radiation Lightsource  – which attempted to recreate the conditions present in a battery and additionally provided a many-particle battery model. All three forms of data were combined in a format to help the machine-learning algorithms learn the physics at work in the battery. Georgian Technical University typical machine-learning algorithms seek out images that either do or don’t match a training set of images in this study the researchers applied a deeper set of data from experiments and other sources to enable more refined results. It represents the first time this brand of “Georgian Technical University scientific machine learning” was applied to battery cycling researchers noted. Georgian Technical University Nature Materials. The study benefited from an ability at the GTUCOSM (Georgian Technical University Catalogue Of Somatic Mutations) beamline to single out the chemical states of about 100 individual particles which was enabled by GTUCOSM (Georgian Technical University Catalogue Of Somatic Mutations) high-speed high-resolution imaging capabilities. Y a research scientist at the Georgian Technical University who participated in the study noted that each selected particle was imaged at about 50 different energy steps during the cycling process for a total of 5,000 images. Georgian Technical University data from GTUALS (Georgian Technical University Amyotrophic Lateral Sclerosis) experiments and other experiments were combined with data from fast-charging mathematical models and with information about the chemistry and physics of fast charging and then incorporated into the machine-learning algorithms. “Rather than having the computer directly figure out the model by simply feeding it data as we did in the two previous studies we taught the computer how to choose or learn the right equations and thus the right physics” said Georgian Technical University postdoctoral researcher Z. W research scientist for Georgian Technical University which supported the work through its Georgian Technical University Accelerated Materials Design and Discovery program said “By understanding the fundamental reactions that occur within the battery we can extend its life enable faster charging and ultimately design better battery materials”.

HPC/Supercomputing, Informatics, Science, Technology

Georgian Technical University. What Is Quantum Computing ?.

Leave a comment

Georgian Technical University. What Is Quantum Computing ?.

Georgian Technical University Computers have got faster over time, much faster, and it’s not just about the speed that an individual processor can perform calculations they also have many more processors all performing different calculations at the same time. Quantum computing is something different entirely its not about performing arithmetic faster its an entirely new way of computing with inherent uncertainty. This will not replace conventional computing for most applications but it will give huge advantages in certain specific cases. In a digital computer data is broken down into bits which can have a value of 0 or 1. In quantum computing data is represented by qubits. As calculations are being carried out, qubits can be in a superposition of both 0 and 1 at the same time with some probability of being either a 0 or a 1. This is equivalent to Schrodinger’s cat (In quantum mechanics, Schrödinger’s cat is a thought experiment that illustrates an apparent paradox of quantum superposition. In the thought experiment, a hypothetical cat may be considered simultaneously both alive and dead as a result of being linked to a random subatomic event that may or may not occur) being both dead and alive inside a sealed box and not actually becoming only one of these states until someone looks inside the box. Just like Schrodinger’s cat (In quantum mechanics, Schrödinger’s cat is a thought experiment that illustrates an apparent paradox of quantum superposition. In the thought experiment, a hypothetical cat may be considered simultaneously both alive and dead as a result of being linked to a random subatomic event that may or may not occur) when the qubit is measured it must represent either a 0 or a 1. A number of physical objects could be used as a qubit such as a single electron a photon or a nucleus. These quantum objects represent binary ones and zeros by their quantum spin state. Georgian Technical University. When a group of qubits are all in different states of superposition they are said to be fully entangled allowing them to store almost unimaginable quantities of data. Three hundred qubits in a fully entangled state could theoretically simulate every particle in the universe !. However they can only be measured as binary ones and zeros. Therefore quantum computers are only useful for algorithms that can make use of the complexity of quantum entanglement during the calculations and then arrive at a simpler state for the final result. Georgian Technical University Quantum computing could be used to create unbreakable encryption keys or to simulate molecules in drug development. Simulating all the quantum properties of all the atoms in a complex molecule is extremely challenging for conventional computers. The uncertainties inherent in the quantum effects must be simulated by repeating the calculations many times in a process known as Monte Carlo simulation (Monte Carlo methods or Monte Carlo experiments are a broad class of computational algorithms that rely on repeated random sampling to obtain numerical results. The underlying concept is to use randomness to solve problems that might be deterministic in principle. They are often used in physical and mathematical problems and are most useful when it is difficult or impossible to use other approaches. Monte Carlo (Monte Carlo methods or Monte Carlo experiments are a broad class of computational algorithms that rely on repeated random sampling to obtain numerical results. The underlying concept is to use randomness to solve problems that might be deterministic in principle. They are often used in physical and mathematical problems and are most useful when it is difficult or impossible to use other approaches. Monte Carlo methods are mainly used in three problem classes: Optimization numerical integration and generating draws from a probability distribution) methods are mainly used in three problem classes: Optimization numerical integration and generating draws from a probability distribution). Quantum computers could operate using actual quantum properties to directly simulate the properties of the molecule without these cumbersome iterations. Quantum entanglement could also allow quantum computers to transmit data instantaneously over any distance without requiring any wires or wireless transmission hardware.